考虑竖向地震作用的振动控制及其优化研究

目前,MRD结构的分析通常只考虑水平地震动而不考虑竖向地震动的影响,地面的水平运动和竖向运动具有相关性,从而影响控制效果．因此对双向地震耦合作用下MRD结构的理论进行研究,建立动力分析模型并得出运动微分方程．以8层MRD结构为例进行地震反应分析,研究表明,考虑和不考虑竖向地震作用,MRD对结构均有良好的控制作用,但是竖向地震作用的存在,使结构各层的层间位移峰值有不同程度的增加,其增量随着竖向地震作用的增加而增加,因此建议在高烈度地区的建筑物考虑竖向地震作用对结构的影响．建立MRD结构优化设计模型,采用IHGA程序对结构进行优化设计．结果表明, MRD结构在各种工况下的各项地震反应均得到更好的控制．     

Symmetry, Optima and Bifurcations in Structural Design

Motivated by optimization problems in structural engineering, we study the critical points of symmetric, ‘reflected', one-parameter family of potentials U(p, x) = max (f(p,x), f(p, −x)), yielding modest generalizations of classical bifurcations, predicted by elementary catastrophe theory. One such generalization is the ‘five-branch pitchfork’, where the symmetric optimum persists beyond the critical parameter value. Our theory may help to explain why symmetrical structures are often optimal.     

改进的小损伤结构动力学有限元建模方法

在遗传算法或神经网络方法识别结构损伤位置和程度时,都是基于少量的在线测量的损伤结构振动响应数据和大量的模型仿真数据来实现的,因而建立高效和精确的损伤结构动力学有限元模型,以便仿真获得损伤结构的大量动力学响应数据是十分重要的基础前提工作。本文针对ANSYS结构分析软件在建立结构小损伤有限元动力学模型存在两个关键问题,结构损伤处直接网格划分的计算结果误差和网格节省问题,以结构损伤振动检测的实际需要为出发点,提出了建立含小损伤结构的ANSYS动力学建模技术,研究了结构局部小损伤及其位置与所在处单元刚度矩阵变化的数量关系。     

Effect of air gaps on ballistic resistance of targets for conical impactors

High velocity penetration of a rigid conical impactor into a ductile target with air gaps between the plates is studied using the cylindrical cavity expansion approximation describing impactor–target interaction. It is showed that the latter model predicts improvement of the ballistic performance of the target with the increase of air gaps. It is found analytically that the ballistic limit velocity of the target consisting of N plates with a fixed total thickness with large air gaps increases with the increase of N. The conditions are discussed when the predicted effects can be most pronounced.     

结构局部非线性修改灵敏度分析及其应用

以线性系统的非线性修改方法为基础，导出了局部非线性振动的灵敏度分析方法；提出了灵敏度为指导的优化设计思想，并将其应用于大型结构上的局部非线性因素的优化设计。文中介绍一些典型非线性特征的数学描述。最后，本文以火炮结构中的炮口振动为例，提出在炮口处增设炮口减振器的设计思想，并用本文方法对炮口减振器的参数进行优化设计，得到满意的结果。     

区段混合能的偏微分方程

结构力学与最优控制模拟关系的共同基础就是分析力学，表明在结构力学与最优控制理论的架构内也应有分析力学的整套理论。传统分析力学总是考虑连续时间、同时的状态、不变维数的体系。并且物性为即时响应的。但结构力学有限元要考虑离散坐标、不同坐标状态、而且变动维数、时滞的体系。根据区段变形能只与其两端位移有关，就可通过数学分析得到Lagrange括号与Poisson括号等内容。区段变形能就是作用量，满足Hamilton-Jacobi方程。但还有区段混合能的表示，本文证明它满足雷同的偏微分方程。它们在离散体系时还有偏差分方程。本文进一步给出了其与Riccati方程的关系。     

结构阻尼模型及系统时域动响应

振动界对经典的非频变结构阻尼模型一直有种种争议,本文检查了它的前提并指出将该模型推广到系统时域动响应分析时导致的悖论.为了提供结构阻尼系统的时域动响应实用分析方法,文中分别提出了基于响应优势谱成份的粘性阻尼近似模型和基于粘弹性理论的三参数频变结构阻尼模型;它们既可逼近结构阻尼缓频变的特性,又可保证系统的时域动响应具有因果性.     

Non-linear viscoelastodynamic equations of three-dimensional rotating structures in finite displacement and finite element discretization

This paper deals with the non-linear viscoelastodynamics of three-dimensional rotating structure undergoing finite displacement. In addition, the non-linear dynamics is studied with respect to geometrical and mechanical perturbations. On part of the boundary of the structure, a rigid body displacement field is applied which moves the structure in a rotation motion. A time-dependent Dirichlet condition is applied to another part of the boundary. For instance, this corresponds to the cycle step of a helicopter rotor blade. A surface force field is applied to the third part of the boundary and depends on the time history of the structural displacement field. For example, this might corresponds to general unsteady aerodynamics forces applied to the structure. The objective of this paper is to model the non-linear dynamic behavior of such a rotating viscoelastic structure undergoing finite displacements, and to allow small geometrical and mechanical (mass, constitutive equations) perturbations analysis to be performed. The model is constructed by the introduction of a reference configuration which is deduced from the non-linear steady boundary value problem. A constitutive equation deduced from the Coleman and Noll theory concerning the viscoelasticity in finite displacement is used. Thereafter, the weak formulation of the boundary value problem is constructed and discretized using the finite element method. In order to simplify the mathematical study of the equations, multilinear forms are introduced in the algebraic calculation and their mathematical properties are presented.     

Effect of the grain size on the macroscopic response of aluminum to shock loading

Shock tests of two lots of a 1420 aluminum-lithium alloy are performed. The mean grain size is 24 μm in the first lot and 1.6 μm in the second lot obtained by the method of equal-channel angular pressing. Two characteristics of dynamic strength of the material were determined in experiments on the high-velocity impact of flat samples: threshold of dynamic stability with respect to compression on the fore front of the compression pulse and spall strength of the material. The materials of both types have an identical threshold of dynamic stability with respect to compression, whereas the spall strength of the microcrystalline alloy is 20% greater than the spall strength of the polycrystalline alloy. The reason is the consumption of energy on structure formation in the coarse-grain material in passing to a larger-scale structural level (in the case with a fine-grain material, such a structure is available in the initial state). The experiments reveal the presence of a second plastic front whose amplitude is approximately 10% of the first plastic front. __________ Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 48, No. 6, pp. 135–146, November–December, 2007.     

三尖杉酯碱侧链酸的不对称合成及结构表征

以N-Boc苏氨醛为起始原料,经Wittig、Meisenheimer重排和催化氢化系列反应,不对称合成了天然产物三尖杉酯碱的侧链酸,中间体及目标产物结构经核磁共振(1 H NMR、13 C NMR)、红外光谱和质谱表征.结果表明,所用合成方法具有产率高、反应条件温和、操作简单等优点;目标化合物的总收率达30%.